• User manual Latte+ (original instructions)

  • With this link you will be forwarded to the user manual Swipe Guide

Components tour

• Milk pump

  • Milk pump

    Transports the cold milk from the fridge to the milk unit.

• Milk mixer

  • Milk mixer

    Cold milk is pumped through two rotating cylindrical gears. By injecting a specific amount of air at the inlet, a cold liquid micro foam or even thick micro milk foam is created.

• Air pump

  • Air pump

    Pump air into the cold milk from the fridge just before enters the milk mixer starts transform it into milk foam

    • No air: liquid milk (cold)
    • Low air: fluid micro foam (cold)
    • The more air, the thicker the milk foam (cold)

• Heater

  • Flow heater

    The micro milk foam which is created by the milk mixer is ready for use in cold coffee drinks.

    By passing the cold micro foam through a flow heater, a perfect heated milk foam is created for a delicious Cappuccino, Latte Macchiato, etc.

    There are two flow heaters placed in serie used to carefully heat up the cold micro milk foam.

  • Flow heater

    • 2 heaters in serie
    • First heater is regulated to 50 °C, second heater is regulated to specified temperature.

    Each heater:

    • Integrated temperature sensor
    • Integrated temperature fuse

• Control board Latte+

  • Control board

    The control board is in constant connection with the Coffee machine and receives the command which preset milk product must be dispensed.

• Inlet valve

  • Inlet valve + pressure regulator [1011446]

    • Coil; 24Vdc  
    • Inlet; G 3/4" with dirt filter
    • Outlet; Ø 6mm with non return valve
    • Pressure regulator; 0,4 bar

  • Internal view

• Dispensing valve Latte+

  • Double manifold valve [1013082]

    Used in Latte+ as cold milk select inlet valve and Hot water & milk dispense valve 

    Spec's

    • Coil; 24Vdc / 11,8W  
    • Body: PPSU
    • Seal: EPDM
    • Opening: DN 2.0 
    • Inlet/outlet; Ø 6mm push-in

• Drain valve

  • Single valve [1013083]

    Used as drain valve to transport the milk, waste water and cleaning detergent to the drain.

    • Coil; 24Vdc / 11,8W 
    • Body: PPSU
    • Seal: EPDM
    • Opening: DN 2.0 
    • Inlet/outlet; Ø 6mm push-in

• Flowmeter

  • Flow meter [1007302]

    Measures the volume of water which enters het Latte+ unit. 

    Also used in the OptiMe, OptiMe X, OptiBean X (model 2026)

    • Inlet nozzle size: Ø 1.8mm
    • 1300 Pulses/litre

• 24V power supply

  • Power supply 24Vdc [1010214]

    Used in OptiBean X , OptiMe X, OptiMe, Latte+

    • Input: 200 - 240Vac / 50 - 60 Hz
    • Output: 24Vdc
    • Output power: 96W (4 A)
    • Lifetime: 60.000 hour (7 year) 

    Fuse [03391]

    • 6,3 A slow
    • Fuses the 230Vac circuit

• EMI /RFI Filter

  • EMI / RFI filter

    The purpose of the RFI/EMI filter is to filter out high-frequency noise currents (conducted RFI or EMI) present on the power lines and signal lines. 

    This prevents these conducted noise currents from entering or exiting the filtered device, allowing the device to function smoothly without disrupting other connected equipment. 

  • Construction and working principle of RFI/EMI Filter:

    Generally, the RFI or EMI filters' design utilizes passive circuit elements such as capacitors, inductors, and in some cases resistors to attenuate both conducted and radiated RFI/EMI. 

• Fridge principle of operation

  • Principle of operation

    Any mechanic knows the basic operation of a refrigerator by heart. However, here are a few features:

    • The cold airflow is moved through the insulated compartment of the refrigerator by means of a fan.
    • Any condensation dripping from the evaporator [1] when the cooling is not active runs through a hose to a shallow plastic collection tray located under the refrigerator.
    • In this tray is the return section of the cooling circuit, which is still warm. This heat is used to evaporate the condensate. 
    • Therefore, when moving a refrigerator that has just been switched off, some water may occasionally run out from under this tray.

  • Rating plate fridge

    The next pages shows how to reach the;

    • Evaporator & fan (front)
    • Condensor & fan (rear)
    • Condensate tray (Bottom fridge)

  • Evaporator & fan (internal ventilation cover removed)

    • Fan
    • Evaporator
    • Temperature sensor
    • Condens outlet which leads to the condens tray under the fridge

  • Condensor with fan (rear panel removed)

  • Condensor without fan (rear panel removed)

  • Condensate tray (Bottom fridge)

    • condens tray with spiral which evaporate the condensate coming from the evaporator.

Installation

• Installation

  • You will be redirected to the user manual.

• Commisioning

  • Commisioning

    You will be redirected to the user manual.

• Activate Latte+

  • Before activating the milk system be sure you Installed and connected the Latte+ system with the Coffee Machine with the data cable. 

    The data cable is part of the included accessories 

  • • Enter the SERVICE MENU
    • Select 03 SETTINGS
  • • Select 05 ADD-ONS

  • Activate the Milk system

    • Activate the ON/OFF switch 
    • Press SAVE
    • For additional settings press MILK SYSTEM.

• Set milk types

  • • Enter the SERVICE MENU
    • Select 03 SETTINGS
  • • Select 05 ADD-ONS
  • • Select 06 MILK SYSTEM

  • LATTE+ MILK SYSTEM

    • Milk system is CONNECTED (ON)
    • SELECT MILK TYPE(S), continue to the next page
    • SET/CHANGE MILK ICON, future option

    Some of settings are future options and are not working

    Power

    • HIGH/ LOW 

    Rinse due t Lactose (risk)

    • RINSE BEFORE DISPENSING 

    Plant-based milk

    • TIME TO STIR/SHAKE AGAIN

  • Number of milk types

    • Set here the number of milk types you want to use.
    • See the pictogram overview under 'TIP'

    Loaded variant milk 1

    • Select which type of milk you use (for example Diary milk), the machine will use the best possible pre-settings.

    Loaded variant milk 2

    If only one type of milk is used this list is inactive

    • Select which type of milk you use (for example Vegan based milk), the machine will use the best possible pre-settings.
    • Press SAVE

  • See here an example of the end result.

• Set milk consistency & temperature

  • Column LEFT

    • 3 warm milk setting* 
    • 3 cold milk settings

    *Most of the time you only use WARM- LIQUID FOAM & SOLID FOAM because they are the base for a Cappuccino and Latte Macchiato

  • • SELECT one of the milk consistency's you want to finetune.
    • Correct the TEMPERATURE, recommended: 

    - milk: 65°C is recommended,

    - plant based (oat) milk: 60-62°C

    • Set the amount of AIR

    - more air: the milk is getting thicker

    - less air: the milk becomes more liquid

    • Set the sample TEST TIME 

        - 5 seconds is about a sample of a a small cup.

    • Press TEST

     - you can test as long as you need

• Rinse machine settings

  • Rinse machine

    The rinsing program need to be activated once a day. The following rinsing setting can be altered:

    Coffee machine settings

    • Rinsing moment
    • Mandatory rinsing 
    • Automatically rinsing 
    • Rinsing brewer only / brewer & mixer 

    Milk settings

    • Sound warning signal and volume settings
    • Milk rinse moments
  • • Enter the SERVICE MENU
    • Select 05 SERVICE NOTIFICATIONS
  • • Select 01 RINSE & CLEAN MESSAGES

  • Rinse coffee machine settings

    Concerns the rinse settings from the Espresso- and Mixer unit inside the coffee machine.

    RINSING (whatever comes first)

    • CUPS: after x cups
    • DAYS after x days (factory = 1 day) 

    RINSING OBLIGATED (On/Off)

    • Mandatory rinsing ON = no rinse program executed no drinks next day.

    AUTOMATICALLY (On/Off)

    • By pressing the button automatically two rinse moments can be set (see alternative tab) and/or a rinse can start after a set number of prepared drinks.

    Selection

    • Rinsing brewer only 
    • Rinsing brewer & mixer 

  • Rinse Latte+ unit settings

    Concerns the rinse settings from the milk circuit inside the Latte+ unit.

    RINSING MILK

    • WARNING SIGNAL [ON] : Switch here the signal which is sounding just before a milk rinsing starts. 
    • VOLUME WARNING SIGNAL [80%]: set here the volume you prefer.
    • TIME [10min]: The time the automatic milk rinse starts after the last milk drink (e.g. Cappuccino). The rinse time can be delayed for up to 20 minutes.

• Cleaning machine settings

  • Clean machine 

    The cleaning program need to be activated once a day. The following cleaning setting can be altered:

    Coffee machine settings

    • Cleaning moment 
    • Mandatory cleaning 

    Milk system settings

    • Link your milk cleaning program to your coffee machine cleaning program.
    • Program a fixed milk clean moment
  • • Enter the SERVICE MENU
    • Select 05 SERVICE NOTIFICATIONS
  • • Select 01 RINSE & CLEAN MESSAGES

  • Clean coffee machine settings 

    Concerns the clean settings from the *Espresso- and Mixer unit inside the coffee machine.

    *Cleaning with tablet

    CLEANING (whatever comes first)

    • CUPS: after x cups
    • DAYS after x days (factory = 7 day) 

    CLEANING OBLIGATED (On/Off)

    • Mandatory cleaning ON = no cleaning program executed: no drinks next day.

  • Cleaning Latte+ unit settings

    Concerns the cleaning settings from the milk circuit inside the Latte+ unit.

    CLEANING MILK

    RINSE BREWER & MIXER AFTER CLEANING MILK SYSTEM [ON]

    • When the daily milk system is started and the software detects the brewer needs to be cleaned too it will integrate the brewer and mixer system cleaning.

    FIXED TIME [OFF] : 

    • OFF : the milk system need cleaning within 24h + 2h, after this first milk has been filled. No cleaning will block all milk drinks.
    • ON : You can set a fixed cleaning time (e.g. 18.00h) when the milk system at 18.00h stops all milk drink will block. PRESS the button FIXED TIME to set the fixed time cleaning time (see alternative tab). 

• Water filter settings

  • After introduction of the Latte+ milk unit a second maintenance screen is introduced which make it possible to run the OptiMe X /OptiBean X with Latte+ unit with one- or two water filters:

    • one* shared large water filter (e.g. Brita C300)
    • two single smaller water filter (e.g. Brita C150). Each unit counts the usage of its own water intake.

    *default setting 

    • For more information, navigate to Water filter settings OptiMe X
    • For more information, navigate to Water filter settings OptiBean X

Recipe settings

• Set recipes with instant milk

  • How to set a recipe made with instant Topping

    This instruction will show a Cappuccino recipe 

    • Enter the SERVICE MENU
    • Select 02 RECIPES
  • • Select CAPPUCCINO
    • Select 02 ADJUST

  • Screen 1

    Adjust your Cappuccino made with Topping

    • Place the SELECTOR switch to INSTANT

    The following TOTAL drink settings can be adjusted: 

    • Coffee beans (grams)
    • Topping (grams)
    • Cup Volume (volume)

    Swipe to the second screen -->

  • Screen 2

    The following ESPRESSO settings can be controlled

    • Ratio; Water to Brewer <--> Mixer
    • Pre-infusion ON/OFF / Pause (seconds)
    • Tamper pressure brewer (1 - 7 )
    • Test your drink without leaving the menu 

    Swipe to the second screen -->

  • Screen 3

    The following settings can be controlled

    • Instant mixer speed at the start instant process
    • Instant mixer speed at the end instant process
    • The moment the mixer speed 1 change into mixer speed 2 during the instant process.

    Screen 4 is only interesting for Latte+ settings

• Set recipes with diary milk

  • How to set a recipe made with diary milk

    This instruction will show a Cappuccino recipe

    • Enter the SERVICE MENU
    • Select 02 RECIPES
  • • Select CAPPUCCINO
    • Select 02 ADJUST

  • Screen 1

    Adjust your Cappuccino made with diary milk

    • Place the SELECTOR switch to LATTE+

    The following COFFEE settings can be adjusted: 

    • Coffee beans (grams)
    • Cup Volume (volume) = only the Espresso volume (ca. 35ml) needed for the Cappuccino can be adjusted here!
    • Swipe to the next screen -->

  • Screen 2

    The following ESPRESSO settings can be controlled

    • Ratio; Water to Brewer
    • Pre-infusion; ON/OFF / Pause (seconds)
    • Tamper pressure brewer (1 - 7 )
    • Test your drink without leaving the menu
    • Swipe to the second screen --> 

  • Screen 3

    • Can be skipped, no Topping, mixer settings
    • Swipe to the second screen -->

  • Screen 4 (milk type 1 settings)

    • Temperature profile

         - Select WARM or COLD milk

    • Dispense time

         - Set dispensing time LIQUID FOAM (sec.)

         - Set dispensing time SOLID FOAM (sec.)

    • PRODUCT SEQUENCE

    - See detailed explanation in the next instruction

    • TEST as long as there is enough milk in the fridge to fill up de cup with milk foam.
    • SAVE your settings
  • • MILK FIRST

         - the Milk starts first, than Espresso

    • MILK LAST

    - the Espresso starts first, than Milk

    • DELAY TIME (sec.)

    - .....

    • MILK DELAY TIME (%)

    - ......

    • LIQUID FIRST or SOLID FIRST

        - set here the foam sequence

  • Screen 5 (milk type 2 settings)

• Set milk selection buttons

  • How to set milk selection buttons

    In the extreme case, you can let the user choose from 3 types of milk.

    • No milk (just black coffee) Optional setting
    • Coffee made with instant milk*
    • Coffee made with diary milk
    • Coffee made with plant based milk*

    *if available in the machine

  • • Enter the SERVICE MENU
    • Select 02 RECIPES
  • • Select the RECIPE of your choice
    • Select 02 ADJUST

  • How activate milk selection buttons.

    Set the checkbox for each recipe (see red box):

    ⮾ INSTANT

    • Only a Cappuccino with instant Topping can be selected.

    ⮾ LATTE+

    • Only a Cappuccino with diary- or plant based milk can be selected.

    ⮾ BOTH

    • A Cappuccino with all the available milk qualities can be selected

• Number of cup sizes

  • Deze link verwijst je door naar de OptiMe X instructie

• Decaf variant

  • Deze link verwijst je door naar de OptiMe X instructie

Recipe options

• Change milk icon

  • Change milk icon (future option)

    • The icons showed in milk choice screen can be changed if necessary.

  • Milk pictogram library

  • Future option

    • SET/CHANGE MILK ICON

• Change milk name

  • Change milk name

    • The milk name showed in milk choice screen can be changed if necessary.
  • • Enter the SERVICE MENU
    • Select 01 INGREDIENTS
  • • Switch ON if you want to use a custom name
    • Press 03 MILK NAME 1 and/or 04 MILK NAME 2 to type the new name

  • A keyboard appears on the screen

    • Type in you NEW MILK NAME
    • Press SAVE

• Set recipe price

  • Recipe prices

    Each drink made with different milk type can have its own price.

  • Recipe prices

    To set the recipe prices (high/low/Free) 

    • Enter the SERVICE MENU
    • Select 02 RECIPES
  • • Select the RECIPE you want to set the price
    • Select 03 OPTIONS
  • • Select CUP VOLUME AND PRICE

  • When a Latte+ unit is activated, the system allows you to configure up to a maximum of 3 different product prices.

    • Cappuccino with instant Topping (product price normal)
    • Cappuccino with MILK 1 from the Latte+
    • Cappuccino with MILK 2 from the Latte+

    PRICE HIGH 

    • Use Price High only when one price is used for the recipes (drink).

    PRICE LOW

    • Use Price Low when two different prices at pre-programmed times of the day, see instruction Price policy.

  • Example screen

    • Select Cappuccino 
    • The next screen shows 2 milk types with different prices

  • Example screen

    • Select Cappuccino 
    • The next screen shows 3 milk types with different prices

• Allergens info

  • Set allergens info

    Its possible to show allergen information. 

    • The main ON/OFF switch allergen information can be controlled in the OPERATOR MENU / 05 SOUND & VISION.
    • For which allergens to be informed must be set in the SERVICE MENU.
    • For each recipe you can show; Lactose / Soya / Gluten / Wheat, and others.

    The picture sows an example when Lactose and Gluten is selected in the Cappuccino recipe.

  • Set allergens info

    • Enter the SERVICE MENU
    • Select 01 INGREDIENTS
  • • Select 04 ALLERGENS

  • Select for each ingredient used which allergies you want to inquire about.

    After the user made a drink selection the display shows automatically the selected allergens selected for that drink 

• Shake/stir plant based milk

  • Introduction

    Plant based milks - ALWAYS - shake before use! Plant based milks are indeed made from PLANT materials. 

    These milks always contain materials that are heavier than the water added to make the milk. 

    Consequently, gravity quickly causes sediment to form: the water separates from the plant material, causing the plant material to settle at the bottom of your carton or reservoir. Some plant milks are more "affected" by this than others. By getting into the habit of ALWAYS shaking all plant milks before use, you ensure the proper connection and thus the best chance of creating foam. So, shake a new carton well before use, then pour it into your plant based milk container and keep it well chilled in your refrigerator (3 degrees).  

  • New feature from software V1.9.1 July 2026 

    To help you remember to shake/stir the milk well a shake/stir notification is added only when a plant based milk is activated in Latte+. 

    After 4 hours the user get a message to shake/stir the plant milk which is in the fridge. 

    • Setting can be found in the SERVICE MENU / 03 SETTINGS / 05 ADD-ONS / 06 MILK SYSTEM. 
    • Time to stir/shake again is 4 hours (Default) Adjustable between 1 - 8 hours 

  • During use (≡ Menu button Active) 

    When the stir/shake set time has been reached 

    1. The user selected a plant based milk. 
    2. The stir/shake instruction on the screen appears. 
    3. Open the fridge and stir/shake the plant based milk.
    4. After confirmation, the selected drink can be started. 
    5. After the set stir/shake hours expired again this instruction must be repeated.  

  • During use (≡ Menu button OFF)

    When the stir/shake set time has been reached the OPERATOR only can reactivate the milk again. 

    1. In the bottom line of the Recipe display shows ‘SHAKE/STIR milk’
    2. The plant based milk will be disabled.  
    3. The OPERATOR enters the menu and select the relevant milk fill button. 
    4. The stir/shake instruction on the screen appears. 
    5. Opens the fridge and stir/shake the plant based milk. 
    6. After confirmation and leaving the menu the selected drink can be started again. 
    7. After the set stir/shake hours expired again this instruction must be repeated. 

Counters

• Day counters

  • DAY COUNTERS

    • Select the button ANALYSIS or OPERATOR MENU (go to page 4)
  • • The first screen shows the CLEAN & RINSE COUNTERS.
    • Press the → button 2x to navigate to RECIPE COUNTERS DAY

  • RECIPE DAY COUNTERS

    • Day counter overview read only, without reset.
    • Reset only possible in Operator Menu / Counters
    • Download counter to an SD/USB memory for processing counter data in Excel spreadsheet.

    CUSTOMER TOTALS (top of the list) 

    • All drink counters added together.
    • Press the CUSTOMER TOTALS line to open detailed counter information, FREE, PAYED, TEST or JUG (counts per cup).

    COFFEE, etc.

    • Each individual drink counter.

    Example: Press the CAPPUCCINO line to open detailed counter information

    • INSTANT (Cappuccino Topping)
    • MILK 1 (Cappuccino Milk 1)
    • MILK 2 (Cappuccino Milk 2)

    *Free, Prices, Tokens, Test or Jug (counts per cup).

  • DAY COUNTER RECIPES in OPERATOR MENU

    • Select 03 DAY COUNTERS RECIPE

  • RECIPE DAY COUNTERS

    • Day counter overview read only
    • RESET button can be added, see next pages.

    CUSTOMER TOTALS

    • All drink counters added together.
    • Press the CUSTOMER TOTALS line to open detailed counter information, FREE, PAYED, TEST or JUG (counts per cup).

    COFFEE, etc.

    • Each individual drink counter.
    • Press the COFFEE line to open detailed counter information, FREE, PAYED, TEST or JUG (counts per cup).

  • RESET in DAY COUNTERS

    • Enter the SERVICE MENU
    • Select 03 SETTINGS
  • • Select 06 OPERATOR SETTINGS
  • • Slide the KEY to the right.
    • Press SAVE
  • • The RESET button in now ACTIVE
    • Press RESET
    • Confirm with YES is you want to reset the DAY COUNTERS.

• Total counters

  • TOTAL COUNTERS

    • Enter the SERVICE MENU
    • Select 04 COUNTERS
  • • Select RECIPE COUNTERS

  • RECIPE (TOTAL ) COUNTERS

    • TOTAL counter overview read only. 
    • If the DAY counter is reset, the TOTAL counter does not reset.

    AUTOMAT TOTALS

    • Number of dispensed drinks over the entire life of the coffee machine. 
    • This counters are not resettable! 
    • Press the text line to open detailed counter information, FREE, PAYED, TEST or JUG (counts per cup).

    MODEL TOTALS

    • Number of dispensed drinks 
    • This counter only RESET if you change the canister VARIANT.
    • Press the text line to open detailed counter information, FREE, PAYED, TEST or JUG (counts per cup).

  • COFFEE, etc.

    • Each individual drink counter.
    • This counters only RESET if you change the canister VARIANT.

    Example: Press the CAPPUCCINO line to open detailed counter information

    • INSTANT* (Cappuccino Topping)
    • MILK 1* (Cappuccino Milk 1)
    • MILK 2* (Cappuccino Milk 2)

    *Free, Prices, Tokens, Test or Jug (counts per cup).

• Cleaning history milksystem

  • CLEAN & RINSE COUNTERS

    OptiMe X (coffee machine)

    • This counter indicates how often and when (date) the CLEANING & RINSING program program was last performed.

    Latte+ (milk system)

    • This counter indicates how often and when (date) the CLEANING & RINSING program was last performed.

    The Clean & Rinse counters can be written to a SD/USB memory by using the download button.

  • COUNTERS CLEAN & RINSE HISTORY

    • Open the SERVICE MENU
    • Select 04 COUNTERS
  • • Select 05 CLEANING HISTORY MILKSYSTEM
  • • The CLEANING history from the last 30 cleaning processes are displayed.

    You don't need to reset the history, history data older than 30 clean cycles are automatically deleted.

• Operating hours milksystem

  • OPERATIING HOURS MILKSYSTEM

    • Enter the CLEANING MENU screen with the menu button ≡
    • Select the button ANALYSIS

  • OPERATIING HOURS MILKSYSTEM

    This overview shows you all electrical Latte+ components:

    • Outlet valve
    • Milk 1 valve
    • Milk 2 valve
    • Cleaning cycles
    • Inlet valve   

    Cycles: how many times the components has been controlled.

    Time: how long the component has been controlled in Hours / Minutes / Seconds

  • OPERATIING HOURS MILKSYSTEM

    This overview shows you all electrical Latte+ components: 

    • Milk pump
    • Air pump
    • Milk mixer
    • Flowmeter   

    Cycles: how many times the components has been controlled.

    Time: how long the component has been controlled in Hours / Minutes / Seconds

Maintenance

• Latte+ preventive maintenance

  • Latte+ Preventive maintenance

    Each year (12 months) we advice to replace the milk hoses. 

    Art. No. 1013678 (kit)

  • How to RESET the LATTE+ PREVENTIVE MAINTENANCE notification

    • Enter the SERVICE MENU
    • Select 05 SERVICE NOTIFICATIONS
  • • Select 03 WATER FILTER & BREWER
  • • Swipe to the second page
  • • Reset the display message by using the button 'RESET LATTE+ PREVENTIVE MAINTENANCE'

• Latte+ service water filter

  • Latte+ service water filter

    This attention will only appear in the display when the Latte+ unit uses its own water filter and the option Latte+ water filter is ACTIVE, in the Service menu / 05 Service notifications / 03 Water filter & brewer

    • Replace the filter, check the filer capacity you use and correct the Liters (or use the monthly signal) if needed.
    • Reset the counter

• Latte+ component maintenance

  • Yearly recommendations for inspection

    During annual machine maintenance, technicians must perform a general visual and functional inspection, including:

    • Inspection for external leaks
    • Verification of proper milk delivery
    • Verification of proper heating performance
    • Functional check of the conductivity sensors
    • Functional check of the check valves
    • Inspection of seals and O-rings for visible wear or leakage
    • General inspection of hoses and connections

    Every 800 operational hours, an estimated 3-4 years/160.000 milk related drinks, "Service Latte component maintenance" appears in the display and milk module 1013068 should be preventively renewed

• Fridge preventive maintenance

  • Any mechanic knows the basic operation of a refrigerator by heart. However, here are a few features:

    • The cold airflow is moved through the insulated compartment of the refrigerator by means of a fan.
    • Any condensation dripping from the evaporator [1] when the cooling is not active runs through a hose to a shallow plastic collection tray located under the refrigerator.
    • In this tray is the return section of the cooling circuit, which is still warm. This heat is used to evaporate the condensate. 
    • Therefore, when moving a refrigerator that has just been switched off, some water may occasionally run out from under this tray.

  • Picture shows the rating plate fridge

    The next pages shows how to reach the;

    • Evaporator & fan (front)
    • Condensor & fan (rear)
    • Condensate tray (Bottom fridge)

  • Evaporator & fan (front)

    • Open the fridge
    • Unscrew the two screws
    • Remove the cover

  • Visible

    • Fan / Evaporator / Temperature sensor

    Maintenance

    • Condens outlet (check if condens drain is open)

  • Condensor & fan (rear)

    • Remove the fridge rear cover by unscrewing the three screws. 

  • • Remove the fan by unscrewing the two top screws
    • The fan can now lifted of the condensor.

  • Maintenance

    • Remove any dust from the fan blades.
    • Remove dust and debris from the evaporator with a vacuum cleaner or brush to maintain proper airflow and allow the fan to efficiently dissipate heat.
    • Place the fan and back panel back in reverse order.

  • Condensate tray (Bottom fridge)

    • Picture shows an unscrewed condens tray with spiral which evaporate the condensate which arrives from the evaporator compartment.

Repairs

• Replacement milk unit

  • When your Latte+ is not producing milkfoam anymore, or certain error codes occur, and you are certain that its not about settings-adjustments in your OBX-OMX ect.ect. you can decide to replace the internal milkfoam unit 1013068 completely.

    The first year you are only allowed to do so regarding warrenty restrictions. No seperate parts which are part of this unit are covered the first year.

    This swipeguide will show you how to swap-test-clean this milk unit in order to get your Latte+ machine producing perfect milkfoam again.

  • 1. Switch off the machine
    2. Take out the power cord
    3. Take out all 4 screws 

    NOTE: Keep drain connection, water supply hose and connection cable towards the OBX/OMX in place and functional if possible.

  • Separate your Latte+ unit from your machine

    1. Move Latte+ to the right
    2. Take the black outlet from the milkhose
    3. guide the milk hose through the sidewall
  • 1. Take off the milk hose from MILK-OUT outlet
    2. Remove the milk hose 
  • 1. Take off the circlip on the inside (see Tip)
    2. Remove the plastic tube from the sidewall
  • 1. Remove all 3 frontside screws
    2. Remove the 1 inside screw

  • Now slide the complete hood upwards and remove it

  • Take out this connector

    TIP: Take a picture for yourself of the electronics before removing connectors following the next steps

  • Remove the wiring from this cable clip

  • Take out these 2 connectors

  • Remove the wiring from this cable clip

  • Remove this connector

  • Remove this connector

  • 1. Take of the blue wire
    2. Take off the brown wire

  • Remove this clamp

  • 1. Place a towel underneath the milkpump
    2. Remove the hose from the old milkpump using a flat-sided screwdriver 

  • Take off this clamp

  • Take off this tube using a small flat-sided screwdriver

  • Release these 2 screws by 2 turns, anti-clockwise

  • Release these 2 screws by turning them anti-clockwise 2 turns

  • Move the complete unit to the left

  • Take the milk unit out this way

  • Clean the area wiht a soft, wet cloth

  • Preparing the new milk unit

    • Take off this clamp

  • Remove the hose, using a small flat screwdriver

  • Take off this white cap

  • 1. Place the new milk unit with the 4 slob-eyed holes over the 4 M4 screws
    2. Move the complete unit to the right (lock position)

  • Secure the new milk unit by tightening the 4 screws again

  • Connect this hose to the heating element outlet

  • Refit the clamp

  • Fit the red hose unto the milkpump

  • Refit the clamp

  • Refit these 2 connectors

  • 1. Refit these 2 connectors
    2. Fit the wiring into the clamp again

  • Fit the wiring into the clamp

  • Fit this connector

    NOTE: upper connector!!

  • Refit this connector

  • Preparing for a function test and visual inspection

    • Refit the milk hose like this
    • Let the milk outlet hang into a bowl freely
    • Fit the milk intake-hose into a milk carton
    • Place the milk carton in the fridge
    • Close the door
  • 1. Refit the power cord
    2. Switch on the Latte+

    NOTE: The new electronic board of the milk unit is automatically updated by the OBX or OMX unit in case the SW version of the milk unit is older than the machine software. 

    No extra actions needed.

  • Activate the milk filling modus on your machine

  • Follow all animated steps in the screen

  • 1. Take multiple milk based drinks like Cappuccino and Latte Macchiato
    2. Make sure the proper foam is produced again by inspecting the results in the bowl
    3. If not: adjust like explained here

  • While testing drinks:

    • make sure by visual inspection that there is absolutely no leakage on behalf of the new milk unit or the other parts of the Latte+

  • Also inspect this side of the unit visual on leaks

  • When everything is okay:

    • Clean the Latte+ by starting the milk cleaning on your OBX or OMX
    • Activate the milk system cleaning

  • Follow all animated steps shown in the display

  • Add the tablet to the cleaning reservoir

  • 1. Place the cleaning reservoir
    2. Run the cleaning program until the end

  • During the cleaning program:

    • extra inspect the parts of the unit on behalf of leaking, functioning ect.ect.

  • When inspection was successfully and no leaks:

    • Switch off the Latte+

  • After the milk cleaning program:

    • Remove the cleaning container
    • Remove the milk hose

  • Refit the hood by sliding it downwards:

    • Frontside like this

  • Back-side like this

  • Refit and tighten all 4 screws on the back-side

  • Refit and tighten the 3 screws on the front-side and the 1 on the inside

  • Replace the tube:

    • upper hole for OBX
    • lower hole for the OMX

  • Refit the plastic circlip to secure the pipe

  • • Refit the milk hose 
    • Fit the hose through the black pipe

  • Fit the Latte+ unit next to the OBX-OMX again, making sure the milk hose is not obstructed or damaged and the plastic pipe goes inside the machine

  • Fit the outlet to the milk hose

  • • Fit the outlet to the bracket
    • Close the door

  • Now your Latte+ is ready for use again

• Input signals check

  • How check some of the Latte+ inputs 

    • Enter the SERVICE MENU
    • Select 06 HARDWARE
  • • Select 01 INPUTS

  • Menu 2.6.1 shows you the inputs signals from the coffee machine.

    • To check some of the inputs from the Latte+ unit swipe to te next page on the display.

  • The following input signals can be checked

    When the checkbox is active (v) the sensor in question been detected.

    The next pages informs you where the sensors are located.

    • Milk system communication error 
    • Milk 1 present 
    • Milk 2 present
    • Cleaning reservoir present

  • Communication error

    A checkmark (✓) indicates that communication between the coffee machine and the Latte+ milk unit has been lost (See TIP).

    Check:

    • Communication cable connectors on both ends.
    • Internal wire looms.
    • Connections to the main board of the coffee machine and the milk controller board.

  • Milk sensors

    1. Remove milk tube 1 or 2, depending on which light sensor you want to check.
    2. Carefully insert a screwdriver into the sensor opening.
    3. When the sensor detects the screwdriver, a checkmark (✓) will appear on the display (See TIP).
    4. Remove the screwdriver from the sensor opening.
    5. The checkmark (✓) should disappear again, confirming that the sensor is functioning correctly.

     

  • Cleaning canister detection

    The presence of the cleaning container is monitored by a reed sensor.

    A magnet integrated into the cleaning container lid is used to detect whether the container is correctly positioned. When the cleaning container is installed correctly, the reed sensor detects the magnet inside the lid and a checkmark (✓) appears on the display (see TIP).

    If the checkmark (✓) is not displayed:

    • Verify that the cleaning container is correctly installed.
    • Check that the magnet is present in the container lid.
    • Inspect the reed sensor and its wiring for damage or loose connections.

Milk system related messages

• Milk system fail

  • Milk system fail

    Result 

    • Latte+ unit disabled

    Problem 

    • No connection between OMX/OBX and Latte+

    Solutions

    • Check if the Latte+ unit is switched ON.
    • Data cable (internal/external) not connected.
    • Cable break / Defective connector.
    • Latte+ PCB defective (worst case).

  • Milk system fail

    • Bad Latte+ data connection possible  
    • Replace internal cable art.no. 1013342
    • Cable is located between Main in PC board and rear side from the OptiMe X

  • Example Milk system fail message

    • Movie from bad contact in internal data cable (in the coffee machine)

  • Example Milk system fail message

    Movie from bad contact in internal data cable (coffee machine)

    Picture:

    Bad contact in internal data cable (coffee machine)

• Latte cleaning container present

  • Cleaning bin + lid is in the fridge.

    Recipes are blocked and cannot be filled either.

    • Remove the cleaning bin

• Out of milk

  • OUT OF MILK

    After filling and dispensing, milk sensor no longer detects milk in milk tube 

    • No milk in tube
    • Milk sensor contaminated

• Out of milk left

  • OUT OF MILK LEFT

    After filling and dispensing, milk sensor no longer detects milk in milk tube 

    • No milk in tube
    • Milk sensor contaminated

• Out of milk right

  • OUT OF MILK RIGHT

    After filling and dispensing, milk sensor no longer detects milk in milk tube 

    • No milk in tube
    • Milk sensor contaminated

• Milk system needs cleaning

  • Milk system needs cleaning

    When a milk container is filled for the first time* (typically in the morning), the milk system must be cleaned within 26 hours (24 hours plus a 2 hour grace period).

    Once this 26-hour period has expired, the milk system will be locked and cannot be used. After the cleaning cycle has been completed, the milk system will be available for use again.

    *The moment of the first milk fill action of the day is visible in the milk button (see picture). 26h after the recorded time the milk system will be clocked.

• Milk system not filled

  • Milk system not filled

    • The machine indicates this when the Latte+ has been cleaned and the milk has not yet been filled/primed.
    • No filling procedure has been started yet / filling procedure failed due to milk not being detected on the sensor.

• Service Latte waterfilter

  • Service Latte water filter

    The waterfilter counter has reached its capacity.

    • Replace the water filter connected with the Latte+ unit
    • Reset the counter in the SERVICE MENU: 
    • Reset the counter in the Service Menu: 05 SERVICE NOTIFICATIONS / 03 WATER FILTER & BREWER / RESET WATER FILTER COUNTER

• Service Latte preventive maintenance

  • Latte+ Preventive maintenance

    • Each year (12 months) we advice to replace the milk hoses, art. No. 1013678 (kit)

  • Reset in Service Menu

    • 05 SERVICE NOTIFICATIONS
    • 03 WATER FILTER & BREWER
    • RESET LATTE+ PREVENTIVE MAINTENANCE

• Shake/stir milk 1

  • Shake/stir milk 1 = left side

    • Plant based milks - ALWAYS - shake before use! 
    • Plant based milks are indeed made from PLANT materials. 
    • These milks always contain materials that are heavier than the water added to make the milk. 
    • Consequently, gravity quickly causes sediment to form: the water separates from the plant material, causing the plant material to settle at the bottom of your carton or reservoir. 
    • Some plant milks are more "affected" by this than others. 
    • By getting into the habit of ALWAYS shaking all plant milks before use, you ensure the proper connection and thus the best chance of creating foam. 
    • So, shake a new carton well before use, then pour it into your plant based milk container and keep it well chilled in your refrigerator (3 degrees). 

  • To help you remember to shake/stir the milk well a shake/stir notification is added only when a plant based milk is activated in Latte+. 

    After 4 hours the user get a message to shake/stir the plant milk which is in the fridge.

    • Setting can be found in the SERVICE MENU / 03 SETTINGS / 05 ADD-ONS / 06 MILK SYSTEM. 
    • Time to stir/shake again is 4 hours (Default)
    • Adjustable between 1 - 8 hours

• Shake/stir milk 2

  • Shake/stir milk 2 = right milk

    • Plant based milks - ALWAYS - shake before use! 
    • Plant based milks are indeed made from PLANT materials. 
    • These milks always contain materials that are heavier than the water added to make the milk. 
    • Consequently, gravity quickly causes sediment to form: the water separates from the plant material, causing the plant material to settle at the bottom of your carton or reservoir. 
    • Some plant milks are more "affected" by this than others. 
    • By getting into the habit of ALWAYS shaking all plant milks before use, you ensure the proper connection and thus the best chance of creating foam. 
    • So, shake a new carton well before use, then pour it into your plant based milk container and keep it well chilled in your refrigerator (3 degrees). 

  • To help you remember to shake/stir the milk well a shake/stir notification is added only when a plant based milk is activated in Latte+. 

    After 4 hours the user get a message to shake/stir the plant milk which is in the fridge.

    • Setting can be found in the SERVICE MENU / 03 SETTINGS / 05 ADD-ONS / 06 MILK SYSTEM. 
    • Time to stir/shake again is 4 hours (Default)
    • Adjustable between 1 - 8 hours

• Shake/stir milk

  • Shake/stir milk

    • Plant based milks - ALWAYS - shake before use! 
    • Plant based milks are indeed made from PLANT materials. 
    • These milks always contain materials that are heavier than the water added to make the milk. 
    • Consequently, gravity quickly causes sediment to form: the water separates from the plant material, causing the plant material to settle at the bottom of your carton or reservoir. 
    • Some plant milks are more "affected" by this than others. 
    • By getting into the habit of ALWAYS shaking all plant milks before use, you ensure the proper connection and thus the best chance of creating foam. 
    • So, shake a new carton well before use, then pour it into your plant based milk container and keep it well chilled in your refrigerator (3 degrees). 

  • To help you remember to shake/stir the milk well a shake/stir notification is added only when a plant based milk is activated in Latte+. 

    After 4 hours the user get a message to shake/stir the plant milk which is in the fridge.

    • Setting can be found in the SERVICE MENU / 03 SETTINGS / 05 ADD-ONS / 06 MILK SYSTEM. 
    • Time to stir/shake again is 4 hours (Default)
    • Adjustable between 1 - 8 hours

Errors

• Reset Latte+ error

  • Latte+ Errors

    • If a Latte+ system error occurs, it will be displayed at the bottom of the screen.
    • In this case, only the Latte+ system will be deactivated; the coffee machine will continue to operate normally.

  • Reset a LATTE+ error

    • Enter the OPERATOR MENU
    • Select 08 RESET MILK SYSTEM

    If this function is not active, please follow the next instructions.

  • • Press OK to reset the milk system error

  • How to activate or deactivate the RESET Latte+ error button in the OPERATOR MENU

    • Enter the SERVICE MENU
    • Select 03 SETTINGS
  • • Select 06 OPERATOR SETTINGS
  • • Activate or deactivate the RESET MILK SYSTEM in Operator menu
    • Press SAVE

  • From Software V1.9.1 the RESET MILK SYSTEM is added on the SERVICE MENU.

    SERVICE MENU / 03 SETTINGS / 05 ADD-ONS . MILK SYSTEM / REST MILK SYSTEM

• Unintended message "Service Latte+" in display

  • Due a bug in SW version V1.8.1-V1.8.2. and V1.8.3 current machines the Latte+ unit can show "service Latte+" in the lower display

    Please proceed and reset counters like shown in this swipeguide to get the message resetted.

    The second filter option is standard on 9 liters in mentioned SW versions above, (unintended) and therefore "Service Latte+" occurs after 9 liters water is taken.

  • • Turn the counters off, or, - when using 2 separate waterfilters for OMX and Latte+ module- , set the correct amount of liters for the actual filter used
    • Push "SAVE" 

• Latte+ error log

  • • Enter the SERVICE MENU
    • Select 07 ERROR MESSAGES

  • READ ERROR LOG

    • Error number / Date / Time 
    • This overview shows you the last 30 error messages.
    • The most recent error is at the top of the list, the oldest at the bottom.   
    • The error log generally doesn't need to be reset. If the list becomes too long, the oldest error is discarded.

     

  • RESET

    • Confirm with YES to remove the error log.

• E201 NTC heating element 1 defective

  • Flow heater [FTH1] temperature sensor defect

    An abnormal temperature is measured by the NTC measuring the output flow from the first in line flow heater.

    • Condition for the error: NTC measures a temperature below -20°C or higher than 200°C.
    • The NTC is located at the output of the first heater just above the mixer (see picture).

  • The Latte+ PC board is located on the opposite side of the flow heaters

    • Check the NTC connection J11 on PCB board, see next page for detailed information.
    • There is no possibility to readout the resistance/temperature of the NTC in de Hardware test. 
    • Replace NTC if needed
  • • Position NTC sensor [FTH1] on the PC board

• E202 NTC heating element 2 defective

  • Flow heater [FTH2] temperature sensor defect

    • An abnormal temperature is measured by the NTC measuring the output flow from the first in line flow heater.
    • The NTC is located at the output of the second heater at the top of the milk module (see picture).
    • Condition for the error: NTC measures a temperature below -20°C or higher than 200°C.

  • The Latte+ PC board is located on the opposite side of the flow heaters

    • Check the NTC connection J14 on PCB board, see next page for detailed information.
    • There is no possibility to readout the resistance/temperature of the NTC in de Hardware test. 
    • Replace NTC if needed
  • • Position NTC sensor [FTH2]

• E203 conductivity sensor defective

  • Conductivity sensor defect

    Just before the medium (water / milk /cleaner) enters the mixer the conductivity is measured by two probes suspended in the medium.

    • Condition for the error: Measured level < 100 
    • The software recognizes the following mediums by means of the measured resistance: Water = 500 / Milk = 1300 / Cleaning agent = 2500
    • The conductivity sensors are located in the input of the mixer (see picture).

  • The conductivity sensor pins are located to the right of the Latte+ printed circuit board. 

    • Check the wiring on the conductivity sensor pins, (see picture).

  • The Latte+ PC board is located on the opposite side of the flow heaters

    • Check the conductivity sensor connection J18 on PCB board, see next page for detailed information.
    • There is no possibility to readout the value of the conductivity sensor in de Hardware test. 
  • • Position conductivity sensor connection on the PC board.

• E204 heating element 1 overheated

  • Flow heater [FTH1] overheat

    During the milk preparation the medium temperature in the flow heater first in line is constantly monitored. 

    • Condition for the error: Measured medium temperature in the flow heater [FTH1] higher than 95°C

    Possible cause:

    • Milk suction hose is not submerged in the milk.
    • Milk dispensing hose to Coffee machine outlet is blocked/kinked, causes an obstruction of the flow through the heating elements resulting in an undesirable temperature increase.

     Solution:

    • Check if the milk hose(s) are inside the milk
    • Check if the fridge/Latte+ is still in line with the Coffee machine.

  • Milk system wrong configured

    Possible cause:

    When the Latte+ unit is prepare for use for one [1] milk only and the Software is configured for two [2] milk varieties. See link to check your settings.

    Solution:

    Check how the Software is configured

    • One milk varieties = one hose (see picture)
    • Two milk varieties = two hoses

• E205 heating element 2 overheated

  • Flow heater [FTH2] overheat

    During the milk preparation the medium temperature in the flow heater second in line is constantly monitored. 

    • Condition for the error: Measured medium temperature in the flow heater [FTH2] higher than 95°C

    Possible cause:

    • Milk suction hose is not submerged in the milk.
    • Milk dispensing hose to Coffee machine outlet is blocked/kinked, causes an obstruction of the flow through the heating elements resulting in an undesirable temperature increase.

     Solution:

    • Check if the milk hose(s) are inside the milk
    • Check if the fridge/Latte+ is still in line with the Coffee machine.

  • Milk system wrong configured

    Possible cause:

    When the Latte+ unit is prepare for use for one [1] milk only and the Software is configured for two [2] milk varieties. See link to check your settings.

    Solution:

    Check how the Software is configured

    • One milk varieties = one hose (see picture)
    • Two milk varieties = two hoses

• E206 heater element 1defective

  • Flow heater [FTH1] defect

    No temperature increase detected by the NTC when the first flow-through heater (FTH1) is activated.

    • Error condition: No temperature rise is detected while FTH1 is active.
    • The first flow-through heater (FTH1) is located directly above the mixer (see image).
  • • Check the resistance of the flow-through heater (approx. 30 Ω). If no resistance is measured, the heater is defective.
    • Check whether the temperature limiter (Klixon) has tripped. Reset it if necessary.
  • • Check the 230V wiring not connected to the electronic board.

  • Condition: No temperature change when FTH1 active  

    Blocking: No

    Active: Always

    Remark: Heating disabled; recipe continues  

• E207 heater element 2 defective

  • Flow heater [FTH2] defect

    No temperature increase detected by the NTC when the second flow-through heater (FTH2) is activated.

    • Error condition: No temperature rise is detected while FTH2 is active.
    • The first flow-through heater (FTH2) is the second heater directly above the mixer (see image).
  • • Check the resistance of the flow-through heater (approx. 30 Ω). If no resistance is measured, the heater is defective.
    • Check whether the temperature limiter (Klixon) has tripped. Reset it if necessary.
  • • Check the 230V wiring not connected to the electronic board.

  • Condition: No temperature change when FTH1 active  

    Blocking: No

    Active: Always

    Remark: Heating disabled; recipe continues  

Trouble shooting Fridge

• Fridge does not operate

  • • Check on/off switch

  • • Check electrical plug male & female at the rear side.

• Product not cool enough

  • • Check the setting of the thermostat
    • Check is the closing of the door, and secure door gasket seals.
    • Check that the interior fan is operating, and not blocked.
    • Check and clean the condenser.

• Frigde is to noisy

  • • Verify the equipment is level.
    • Ensure that the equipment is not touching other equipment that could cause vibration.

• Fridge monthly maintenance

  • Press link to continue

• Fridge Defrosting

  • Press link below